YAMAHA QL5
āļĢāļŦāļąāļŠāļŠāļīāļāļāđāļē : QL5
āļĢāļēāļāļē |
850,000.00 āļŋ |
āļāļģāļāļ§āļāļāļĩāđāļāļ°āļāļ·āđāļ | |
āļĢāļēāļāļēāļĢāļ§āļĄ | 850,000.00 āļŋ |
āļŠāļīāļāļāđāļēāđāļĄāđāđāļāļĩāļĒāļāļāļ
āļŠāļīāļāļāđāļēāļŦāļĄāļ
āļĢāļēāļĒāļĨāļ°āđāļāļĩāļĒāļāļĒāđāļ : āļāļīāļāļīāļāļāļĨāļĄāļīāļāđāļāļāļĢāđ Digital Mixing Console 32 Analog input, 16 output, 8 Matrix.( Max 64 input via optional i/o ), Superior Dante Networking Built In.Fader configuration: 32 + 2 (Master), Stainless steel iPad support stays.
āļĢāļēāļĒāļĨāļ°āđāļāļĩāļĒāļāļāļąāđāļāļŦāļĄāļ : YAMAHA QL5 āļāļīāļāļīāļāļāļĨāļĄāļīāļāđāļāļāļĢāđ Digital Mixing Console 32 Analog input, 16 output, 8 Matrix.( Max 64 input via optional i/o ), Superior Dante Networking Built In.Fader configuration: 32 + 2 (Master), Stainless steel iPad support stays.
- Mix channels: 64 mono, 8 stereo.
- Busses: 16 mix, 8 matrix (Input to Matrix supported).
- Local I/O: 32 in, 16 out.
- Fader configuration: 32 + 2 (Master).
- Stainless steel iPad support stays.
specifications
Sampling frequency rateInternal44.1kHz / 48kHzExternal44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (Âą200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (Âą200ppm)Signal delayLess than 2.5ms, INPUT to OMNI OUT, Fs= 48kHzFader100mm motorized, Resolution=1024steps, +10dB to â138dB, ââdB all fadersTotal harmonic distortionLess than 0.05% 20Hz-20kHz@+4dBu into 600ÎĐ, INPUT to OMNI OUT, Input Gain= Min.Frequency response+0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUTDynamic range112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min.Hum & noise levelEquivalent input noise-128dBu typ., Equivalent Input Noise, Input Gain=MaxResidual output noise-88dBu, Residual output noise, ST master offCrosstalk-100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min.Power requirements100-240V 50/60HzPower consumption200WDimensionsW828mm(32.6in)H272mm(10.7in)D563mm(22.2in)Net weight21.8kg(48.1lb)AccessoriesOwnerâs Manual, dust cover, power cord, DVS license sheetOptionsMini-YGDAI cards *2 , Gooseneck Lamp LA1L, Nuendo LiveOthersOperating temperature range: 0 - 40â, Storage temperature range: -20 - 60â
Crosstalk@1kHz : A 22kHz, 30dB/Oct filter is used to measure crosstalk.
Total Harmonic Distortion : An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion.
Hum & Noise : An A-Weight filter is used to measure hum &noise.
Analog input characteristics
Input ConnectorsGAINInput
ImpedanceSource
ImpedanceInput levelConnectorSensitivity*ÂđNominalMax. before clipINPUT
1-32 *6+66dB7.5 kÎĐ50-600 ÎĐ
Mics &
600 ÎĐLinesâ82dBu
(61.6ΞV)â62dBu
(0.616mV)â42dBu
(6.16mV)XLR-3-31
type
(Balanced) *2â6dBâ10dBu
(245mV)+10dBu
(2.45V)+30dBu
(24.5V)
*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level
controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu=0.775 Vms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the console software.
*6. QL1: INPUT1-16
Analog output characteristics
Output
ConnectorsOutput
ImpedanceLoad
ImpedanceMaximum
Output
Level *5Output LevelConnectorDefined LevelMaximum
Non-Clip LevelOMNI
OUT 1-16 *775 ÎĐ600 ÎĐ
Lines+24dB
(default)+4dBu
(1.23V)vt+24dBu
(12.3V)XLR-3-32 type
(Balanced) *1+18dBâ2dBu
(616mV)+18dBu
(6.16V)PHONES15 ÎĐ8 ÎĐ
Phones-75mW *6150mWStereo Phone
Jack(TRS)
(Unbalanced) *240 ÎĐ
Phones-65mW *6150mW
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND).
*3. 0 dBu=0.775 Vms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position.
*7. QL1: OMNI OUT 1-8
Digital input/output specifications
ConnectorsFormatData lengthLevelAudioConnectorPrimary/SecondaryDante24bit or 32bit1000Base-T64ch Input/64ch
Output@48kHz *1EtherCON Cat5e
*1. QL1: 32ch Input/32ch Output@48kHz
Digital output specifications
ConnectorsFormatData lengthLevelConnectorDIGITAL OUTAES/EBUAES/EBU Professional Use24bitRS422XLR-3-32 type (Balanced) *1
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
I/O SLOT (1-2) specifications
Each I/O Slot accepts a Mini-YGDAI card.
Only Slot 1 has a serial interfac
Control I/O characteristics
ConnectorsFormatLevelConnectorMIDIINMIDI-DIN Connector 5POUTMIDI-DIN Connector 5PWORDCLOCKIN-TTL/75 ÎĐ terminatedBNC ConnectorOUT-TTL/75 ÎĐBNC ConnectorGPI (5IN/5OUT)--D Sub Connector 15P(Female) *1NETWORKIEEE802.310BASE-T/100Base-TXRJ-45LAMP (QL5: x 2, QL1: x 1)-0V-12VXLR-4-31 type *2USB HOSTUSB 2.0-USB A Connector (Female)